POWER FLEX                  

CLASSIFICATION: C2TES1 according EN 12004

 POWERFUL FLEXIBLE RESINOUS ADHESIVE FOR TILES

IDEAL FOR INSTALLING BIG DIMENSIONAL TILES IN INNER OR OUTER SPACES WITH HIGH DEMANDS

 

DESCRIPTION

Cement –based, powerful, resinous and flexible adhesive for tiles, of high strength. It is produced under standard modern industrial conditions with quarries of special granule measurement of high clarity. It contains special polymer resinous mixed additives of highest quality and technology of the most approved European manufacturers, which offer accordingly many advantages such as: Powerful initial and final agglutination. Great flexibility and strength against deformations and cracks. Reduced slide and long duration for workability. Great resistance against humidity and temperature fluctuations (heat-cold). Great  workability and easy to apply. It is categorized as an adhesive type under the category C2TE S1 according to the European Standards EN 12004 and EN 12002.

Use

It is used for the application of every type of tiles, (floor or wall), marbles, natural granites and decorative stones. It is suitable for applying on absorbent or non –absorbent surfaces. It offers great long lasting results and is ideal for the adhesive of big dimensional tiles in very demanding spaces such as vibrating floors,  floors with under-floor heating,  plasters, swimming pools, terraces, industrial spaces of heavy duty, busy spaces, parking spaces etc.

Application

The substrate of application must be thoroughly prepared so that it is free of dust, paint, oils etc. It also has to be free of rotten parts and capable to carry the weight. For rotten substrates or substrates of high absorbance (mortar mixtures) it is necessary to apply the stabilizer product SYSTEM TECHNICA TECHNOFLEX, 1-2 hours prior to the application of the adhesive. For best result before the application it is recommended to wet the surface. The content of the sack is mixed under the analogy of 25kg of adhesive with 6.2 lit (± 0,25 lit) of clear water, until a homogeneous mixture comes up free of lumps. The mixture is then left to mature for 5-7 minutes and then mix it again with a low revolution mixer. The adhesive mixture is ready to use and its coagulation time is 1 to 2 hours depending on the temperature of the environment. During this time the mixture is mixed periodically without adding more water. Coating the adhesive on the surface is uniformly applied by means of a suitable notched trowel. The mixture that is applied must be covered with tiles within 30 minutes.

Especially for non absorbent tiles of big dimensions ( 60χ60 or over). It is recommended that the application of the adhesive, in addition to the surface, should also be done evenly with a spatula at the back side of the tile giving the thickness of 1mm. In that manner and also using special levellers we can achieve an easy application and secure permanent agglutination.

Application temperature is between 5° C and 35 ° C.

Consumption

2.5- 4.52kg /m², depending on the trowel’s notch size, tile size and the nature of the substrate.

Storage

Keep in a room with low humidity and still on pallets up to one year from the date of production and always in sealed package

Packaging

Provided in bags of 25kg

VETRO ACRYLIC ADHESIVE OF GLASS-BRICKS

Characteristics-Application

Special acrylic glue for placement of glass-bricks. Due to the high durability of the concrete, of the chosen aggregates and the special scrylic addings that it contains, it gives the possibility of use both indoors and outdoors (walls and floors), as it secures excellent waterproofnes.

Packaging
Sacks of 25Kg.

 system-technica-vetro-new

 

 

 

 pdfVETRO-ENGLISH.pdf

 

 


 

 

 VETRO

 

                                                                                                                         VETRO

                                                                                                       ACRYLIC ADHESIVE FOR FIXING THE GLASS BLOCKS

                                                                                                                CLASSIFICATION: C2 TE According EN 12004

Characteristics-Application

Special acrylic adhesive for installation of glass blocks. Due to the high durability of the concrete, of the chosen aggregates and the special acrylic additives that it contains, it enables the use of indoors and outdoors (wall and floor) as it secures excellent sealing.

Instructions of use

The content of the bag is mixed in a ratio of 25 kg of glue with 6.2 liters of clean water ( ± 0.25 liters) until a homogeneous mixture is comes up. The mixture should be left for about 5-7 minutes to settle, before it is slightly stirred again with a low revolution mixer. The glue mixture is ready for use and its coagulation time is 1 to 2 hours depending on ambient temperature. The SYSTEM TECHNICA –VETRO is applied to the substrate with the use of a suitable notched trowel, or a common trowel. The installation of the glass blocks should be done at the latest 20minutes after the application of the adhesive. Moreover the levelling of the blocks should be done within 30 minutes since their placement.

Consumption

Depending on the joint size

                                  

Storage

Keep in a room with low humidity and still on pallets up to one year from the date of production and always in sealed package

                                

 

 

 

 

 


 

 

 VETRO

 

POWER FLEX

CLASSIFICATION: C2TES1 according EN 12004

 POWERFUL FLEXIBLE RESINOUS ADHESIVE FOR TILES

IDEAL FOR INSTALLING BIG DIMENSIONAL TILES IN INNER OR OUTER SPACES WITH HIGH DEMANDS

DESCRIPTION

Cement –based, powerful, resinous and flexible adhesive for tiles, of high strength. It is produced under standard modern industrial conditions with quarries of special granule measurement of high clarity. It contains special polymer resinous mixed additives of highest quality and technology of the most approved European manufacturers, which offer accordingly many advantages such as: Powerful initial and final agglutination. Great flexibility and strength against deformations and cracks. Reduced slide and long duration for workability. Great resistance against humidity and temperature fluctuations (heat-cold). Great  workability and easy to apply. It is categorized as an adhesive type under the category C2TE S1 according to the European Standards EN 12004 and EN 12002.

Use

It is used for the application of every type of tiles, (floor or wall), marbles, natural granites and decorative stones. It is suitable for applying on absorbent or non –absorbent surfaces. It offers great long lasting results and is ideal for the adhesive of big dimensional tiles in very demanding spaces such as vibrating floors,  floors with under-floor heating,  plasters, swimming pools, terraces, industrial spaces of heavy duty, busy spaces, parking spaces etc.

Application

The substrate of application must be thoroughly prepared so that it is free of dust, paint, oils etc. It also has to be free of rotten parts and capable to carry the weight. For rotten substrates or substrates of high absorbance (mortar mixtures) it is necessary to apply the stabilizer product SYSTEM TECHNICA TECHNOFLEX, 1-2 hours prior to the application of the adhesive. For best result before the application it is recommended to wet the surface. The content of the sack is mixed under the analogy of 25kg of adhesive with 6.2 lit (± 0,25 lit) of clear water, until a homogeneous mixture comes up free of lumps. The mixture is then left to mature for 5-7 minutes and then mix it again with a low revolution mixer. The adhesive mixture is ready to use and its coagulation time is 1 to 2 hours depending on the temperature of the environment. During this time the mixture is mixed periodically without adding more water. Coating the adhesive on the surface is uniformly applied by means of a suitable notched trowel. The mixture that is applied must be covered with tiles within 30 minutes.

Especially for non absorbent tiles of big dimensions ( 60χ60 or over). It is recommended that the application of the adhesive, in addition to the surface, should also be done evenly with a spatula at the back side of the tile giving the thickness of 1mm. In that manner and also using special levellers we can achieve an easy application and secure permanent agglutination.

Application temperature is between 5° C and 35 ° C.

Consumption

2.5- 4.52kg /m², depending on the trowel’s notch size, tile size and the nature of the substrate.

Storage

Keep in a room with low humidity and still on pallets up to one year from the date of production and always in sealed package

Packaging

Provided in bags of 25kg

 

 

pdfVETRO.pdf

 

 

 


 

 

TERRA ACRYLIC ADHESIVE FOR MARBLES,NATURAL STONES & PAVEMENT PLATES

Characteristics-Application

Acrylic adhesive for challenging projects,with high durability to extreme temperature conditions. Suitable for the coating of cement, stone, plaster and cotto plates, as well as for the coating of decorative tiles and many other decorative elements. Suitable for the placement of plates either indoors or outdoors.

Packaging
Sacks of 25Kg.system-technica-terra-new

 

 

 

 

 

 

pdfTERRA-ENGLISH.pdf

 

 


 

 

 

RAPID FLEX SPECIAL ACRYLIC TILE

ADHESIVE OF RAPID THICKENING C2TE-FS2

 

Characteristics-Application

Professional, acrylic adhesive for tiles, of rapid congealment, with great gripping ability, high durability to extreme temperature conditions (heat or frost) and excellent durability to any harassment. Suitable for any professional use, for agglutination of any type of ceramic tiles either absorbing or not, of natural stones either indoorw or outdoors areas, walls or floors and subbases: concrete, sloush grouts, plasters, old floors etc. Moreover, the SYSTEM TECHNICA - RAPID FLEX is also suitable for systems of intrafloor heating as well as to areas with constant presence of water and moisture. RAPID FLEX is ready for assemblance within 3 hours.

Packaging
Sacks of 25Kg.system-technica-rapidflex-new

 

 

 

pdfRAPID_FLEX-ENGLISH.pdf

 

 

 


 

FLEXIBLE ELASTIC ACRYLIC TILE ADHESIVE C2TE-S2

Characteristics-Application

Elastic acrylic adhesive for challenging projects, with great gripping ability, high durability to extreme temperature fluctuations and excellent durability to any harassment. Suitable for special ceramic applications, like the placement of tiles on glasses, on gypsum boards, or any type sleek surface, as well as for the placement of tiles on heated floors, wooden surfaces (under conditions) and in areas with acute vibrations as in underground train stations, airports etc, giving antiseismic properties.

Packagingsystem-technica-flexible-new
Sacks of 25Kg.

 

 

 

 

 

pdfFLEXIBLE-ENGLISH.pdf

 

 


 

SUPER ADD SUPER ACRYLIC ADHESIVE FOR ALL TYPES OF TILES C2TE-SI

Characteristics-Application

Super acrylic adhesive for challenging projects,with great gripping ability and high durability to extreme temperature conditions (heat or frost). The special acrylic resins and the cellulose that it contains, makes the agglutination of tiles (any type) Klinker tiles, granite tiles, marbles and natural stones, possible, either ondoors or outdoors, in walls, in floors and in substratums, concrete, slush grouts, plasters, old floors (any type) etc. As well as for agglutination of durable tiles in areas of heavy traffic (as in industries, public areas, schools, hospitals etc). This type of adhesive is also suitable for ths agglutation of big marble tiles or natural stones in walls. The adhesive SYSTEM TECHNICA - SUPER ADD is suitable for areas where the presence of water is constant (like swimming pools, water tanks, underground areas etc.).

Packagingsystem-technica-superadd-new
Sacks of 25Kg.

 

 

 

 

 

pdfSUPER_ADD-ENGLISH.pdf

 


 

 

SUPER ACRYLIC TILE ADHESIVE C2TE

Characteristics-Application

Super acrylic adhesive for challenging projects, with great gripping abilitu, high durability to extreme temperature conditions (heat or frost) and excellent durability to any harassment. Suitable for the application of tiles either indoors or outdoors, for agglutination of ceramic tiles on chipboards, tiles as well as to areas of heavy traffic (sush as in workshops, industries etc).

For special applications we recommend the use of the amplifying emulsion SYSTEM TECHNICA TECHNOFLEX.system-technica-super-new

Packaging
Sacks of 25Kg.

 

 

 

pdfSUPER-ENGLISH.pdf

 


 

PLUS ACRYLIC TILE ADHESIVE C1TE

Characteristics-Application


Acrylic adhesive for tiles, easy to use with extreme durability in bad temperature conditions. It is recommended for dinding ceramic tilew either indoors or outdoors, in walls or floors.

For special applications we recommend the use of the amplifying emulsion SYSTEM TECHNICA TECHNOFLEX.

Packagingsystem-technica-plus-new
Sacks of 25Kg.

 

 

 

 

 

pdfPLUS-ENGLISH.pdf